Revox M 217 Instrukcja Obsługi Strona 1

Konfiguration M217 R45of of M217Wall Display Unit E 2.01

M217 8 1 2 3 4 5 6Installation procedure You should avoid applying any pressure to the display during or after installation. 1) Install the moun

M217 9 Jung / Merten M217 Revox offers the M217 for the Central European market in different designs from the Jung and Merten companies. You can s

M217 10 Installation procedure You should avoid applying any pressure to the display during or after installation. 1) Screw the mounting fixture

Re:control M217 11 Connection plan M217 Setup and operation The wall display must be connected to a Revox Re:system device or a

Konfiguration M217 12 M217 Configuration The basic settings for the M217 are made with the four DIL switches on the back of the unit. Use a small

Re:control M217 13 M217 Address setting Connection to a Re:system device (M10, M100, M51) If the M217 is connected directly to a Re:system device

Konfiguration M217 14 A/B operationA/B Operation: 2 displays control one side room amplifier The Multiroom system from Rev

Re:control M217 15 MAIN MENU The main menu shows you clearly detailed information in the M217 display. The control is effected either by the conne

Operation M217 16 Setting the display contrast The contrast of the display is adjusted by Revox to an optimal reading angle. Depending upon insta

Re:control M217 17 TIMER MENU The Timer is the control centre of the Multiroom system. Using the Timer, you can set a wakeup alarm for specific da

Operation M217 18 Timer selection Timer 1 has been selected in the above example. The individual Timers can be selected with the Timer so

Re:control M217 19 c Switching times Once you have selected a Timer, you can define the switch on/off times with the Select softkey. The first ti

Operation M217 20 d Weekday Once you have defined the switch-on and switch-off timepoints, by pressing the Select key again, you can reach the ne

Re:control M217 21 e Volume After selecting the weekday(s), the next time you press Select, you will be prompted to set the volume level that sho

Operation M217 22 Ç Remote menu Re:system The third option in the Remote menu is to deactivate a source (Fig e). In this case, the

Re:control M217 23 Activate Timer As default, the individual Timers are deactivated. As soon as the switching times of a Timer are modified, the

Operation M217 24 Nested events Through the Timer programming, you can create nested events. Nested events occur when two different events addres

Re:control M217 25 Guarantee The guarantee period is 24 months from the date of purchase. Your dealer should be your first contact if you need se

Appendix M217 26 Technical Data Connections VCC: + 8 to 20 V A: Bus-communication B: Bus-communication GND: Ground / screening Max.

Re:control M217 27

Re:control M217 1 Wall display M217General Installation advice & Multiroom Planer Safety Guidelines Connection schematic M217 GIRA M217 F

Appendix M217 28 M217 Display Operating instructions / Part no.: 10.30.3019

Re:control M217 2 Wall display M217 Please read these instruction through completely and carefully before setting the unit up. General Ideall

Re:control M217 3 Danger warning Improper mounting of this device in an environment with low-voltage products (230 V AC) can cause serious heal

Re:control M217 4 Connection Revox recommends using a 4-lead telephone cable (1 x 4 x 0.5 mm²) with an RJ11 plug (6P4C modular) for connection to

M217 5 GIRA M217 The company Gira offers the M217 wall display, which is compatible with the REVOX Multiroom system. The M217 display unit shows

M217 6 Installation procedure You should avoid applying any pressure to the display during or after installation. 1. Screw the mounting fixture

M217 7 Feller EDIZIOdue 4217.M The Swiss company Feller offers the 4217.M wall display from their EDIZIOdue series, which is compatible with the R